by Jason Stalcup,
published:
syndicated: 2 | total views: 1689 |
word count: 848
laesbarhedsindex readability score: Average Readability
on the net: http://www.generation-homes.com
UNITED STATES, Feb 04 — Crown moulding is one of the lowest cost additions you can make to a home that has possibly the greatest impact and highest return on investment. The addition of decorative moulding enables you to transform any ordinary living space bringing it a new life, charm and elegance. The installation of crown moulding can certainly be a do it yourself type of improvement. Check your measurements and make your cuts
C
rown moulding is one of the lowest cost additions you can make to a home that has possibly the greatest impact and highest return on investment. The addition of decorative moulding enables you to transform any ordinary living space bringing it a new life, charm and elegance. The installation of crown moulding can certainly be a do it yourself type of improvement. However, if you’ve decided to take on your own crown moulding installation project there are some guides you should follow to make your job run smoother and avoid material waste.
First, find out what you need for materials.
You will need to determine what type of moulding and how much of it you will need to buy. You will need to measure and mark your walls for the best estimate on materials. Measure each individual wall and round up to the next foot. If any of your walls measure within a few inches of a length of moulding always buy the next size up just to be on the safe side.
Second - create a plan of attack.
We will be installing each piece of moulding in an ordered sequence, so we should do a quick sketch of the room, top view, as if we were looking down to see which wall we start with. Let’s make this a bit easier and start with the wall opposite the door and then number each wall going counterclockwise. Let’s also set up our guides for installation on the walls. Hold a piece of moulding at each inside and outside corner to mark the position of the bottom edge. Use a chalk line stretched between the two opposite ends to mark the wall for your installation line. Also, locate and mark the position of studs and joists just below the installation line.
Third - install the first length.
Measure your starting wall and cut the first piece of moulding square at both ends using a miter saw. Then align the piece of moulding with your installation line and begin nailing 8d finish nails working from the center out. Make sure that your nails are centered in the moulding between top and bottom.
Fourth - cutting an inside corner joint.
For inside cuts we use a coped cut to ensure that the face of the moulding joins properly. Place the moulding on the saw with the ceiling edge against the table and the bottom edge against the saw fence. Make sure that the saw is set to a 45 degree angle. If you are coping a left side corner swing the saw to the left and right for the right side. You are doing it correctly if the long edge of the moulding is on the back. To make sure that we will have a joint that fits tightly we will now cope the inside corner joint. Mark the face of the moulding with a pen on the very edge of the miter cut. Set your coping saw at a 5 degree angle and use the pen marked edge as your guide. Hold the piece in place on the wall to make sure your fit is tight. Note: Before moving to the next step check to see what type of cut the other end of your moulding needs. If it is another inside corner take a measurement from the top edge of the number 1 piece that you have already installed to this corner. Mark the length of this measurement on your coped moulding and use your miter saw to make a square cut. You can now nail up that piece of moulding.
Fifth - cutting an outside corner joint.
To determine the length of your moulding piece if it ends on an outside corner cut two scrap pieces of moulding at opposite 45 degree angles. Join these pieces together and hold them in place at your outside corner. We can now take a measurement from the top edge of your installed starting piece to the edge of the corner piece you are holding in place. Use that length to cut your coped piece of moulding.
Sixth - The installation process
If the opposite end of your next piece of moulding ends on an inside that does not require a coped end, repeat the measuring and cutting you just did in order to but the outside corner joining end. Then measure and cut the opposite end to but the squared end against the wall. If the opposite end of your next piece of moulding does end in a corner that requires a coped cut repeat step four and complete your outside corner. Lastly, you will work your way around the room in this same way. Cope your inside corners and miter your outside corners. Check your measurements and make your cuts. If you run into problems like excessively uneven walls, ceilings or ceiling heights due to your house settling or shifting consult a professional to avoid any unnecessary cost and aggravation.
Communicate directly with Jason Stalcup, the author of this article. Ask questions, send suggestions, comments, engage in conversation, or perhaps you would like to submit a project.
Click Here to ask a question, send a comment, or proposal.
It can be difficult for homeowners to maintain a home that looks fresh, clean, and like new. In order to keep a home in pristine condition every so often homeowners must engage in some type of home improvement project. The most common among these
When you look at patio covers, you will naturally compare the vinyl patio cover as opposed to the aluminum patio cover. It is always best to look at each cover and their advantages and disadvantages before you make your decision. If you live in an ar
To build a shower cubicle you start with the shower tray. Many people attempt to make one of these themselves by building a box that they cover with some impervious material - usually tiles. However, the construction is not easy because making the bo
So you decided that your home is in need of some new flooring. Perhaps it’s the flooring in one of your bathrooms or maybe even the flooring in the kitchen or living room. Regardless of where you believe new flooring is needed there are a multi
Poor maintenance, harsh weather, and age are some of the major causes of roof damage. Whether it’s a residential, commercial or industrial building,it faces strain and stress especially if you neglect it.
Lately, many structures around t
Swimming pool landscaping design requires planning for the backyard addition. When you get the right design for the landscaping you create an oasis for your swimming pool that is more enjoyable.
A Zero point magnetic power generator is basically a Free Energy Generator. It uses magnets, and magnetic force to induce perpetual motion. It runs by itself, indefinitely without stopping, thus creating completely free electrical energy, which can f
Home improvement can be a tricky subject because it can either require a home equity line of credit just to finish one job or it can be done on a shoestring budget and still look great. Assuming you are pushing for the latter of the two and want to g
Are you looking for the perfect TV stand that matches your television, as well as your home décor? Do you want a TV stand that will complement your sense of style? If so, you will be pleased to know that there is a wide range of TV stands available i
So, you've decided to put your home on the market and it's all cleaned, organized, and repainted but seems to be missing something. Take a look around and notice how much greenery you have living in your home. Healthy houseplants can add a lot of app
When you wish to transform your home or living space into warm and envying environment then a fireplace can do just the trick. You may already have a fireplace, but for some reason your room seems to be lacking the welcoming quality you so desire. In
Wainscoting is a traditional decorative application to walls which has been making a comeback recently. Originally used on the lower portion of the walls in a house to cover the effects of rising dampness from beneath the floor, it is now predominant
It can be hard to know where to start in regards to home improvements. Maybe you have just moved in to a new, modern home and are looking to give it some character or perhaps you want to freshen up an old home, whatever your needs interior moldings c
Crown moulding is one of the lowest cost additions you can make to a home that has possibly the greatest impact and highest return on investment. The addition of decorative moulding enables you to transform any ordinary living space bringing it a new
When it comes to personal taste there is no right or wrong there is only what we as an individual find pleasing. When it comes to your home this is not always true. For instance, if you are planning a home renovation or home improvement project that
Syndication
tweet
PDF version
Printable version
Publisher HTML version
Discussions (1)
Email Article
Styrofoam Molding
»How To Install Crown Moulding Yourself
‘Styrofoam crown moldings would be simple to install with these directions, good write up.’
Rating: 5.0 out of 5.0 based on 1 discussion(s).
Post New Comment